Enables or disables the local computer Windows Time service private log. Controls whether this computer is marked as a reliable time server. A computer is not marked as reliable unless it is also marked as a time server.
Not a time server 0x Always time server 0x Automatic time server 0x Always-reliable time server 0x Automatic reliable time server The default value for domain members is Controls whether or not the chaining mechanism is disabled. If chaining is disabled set to 0 , a read-only domain controller RODC can synchronize with any domain controller, but hosts that do not have their passwords cached on the RODC will not be able to synchronize with the RODC.
Specifies the maximum amount of time that an entry can remain in the chaining table before the entry is considered to be expired. Expired entries may be removed when the next request or response is processed. The default value is 16 seconds. Controls the frequency at which an event that indicates the number of successful and unsuccessful chaining attempts is logged to the System log in Event Viewer.
The default is 30 minutes. Controls the maximum number of entries that are allowed in the chaining table. If the chaining table is full and no expired entries can be removed, any incoming requests are discarded.
The default value is entries. Controls the maximum number of entries that are allowed in the chaining table for a particular host. The default value is 4 entries. Specifies the smallest local clock adjustments that may be logged to the W32time service event log on the target computer. The default value is parts per million - PPM. Indicates the maximum number of seconds a system clock can nominally hold its accuracy without synchronizing with a time source.
If this period of time passes without W32time obtaining new samples from any of its input providers, W32time initiates a rediscovery of time sources. Default: 7, seconds. Controls which events that the time service logs. Time jump 0x2. Source change The default value on domain members is 2. The default value on stand-alone clients and servers is 2.
Controls the rate at which the clock is corrected. If this value is too small, the clock is unstable and overcorrects. If the value is too large, the clock takes a long time to synchronize. The default value on domain members is 4.
The default value on stand-alone clients and servers is 4. Controls the period of time for which spike detection is disabled in order to bring the local clock into synchronization quickly.
Specifies that a time offset greater than or equal to this value in 10 -7 seconds is considered a spike. Maintained by W32Time. Controls the dispersion in seconds that you must assume when the only time source is the built-in CMOS clock.
Specifies the maximum offset in seconds for which W32Time attempts to adjust the computer clock by using the clock rate. Specifies the largest negative time correction, in seconds, that the service makes. Specifies the largest interval, in log2 seconds, allowed for the system polling interval. Specifies the largest positive time correction in seconds that the service makes. Specifies the smallest interval, in log base 2 seconds, allowed for the system polling interval. Controls the rate at which the phase error is corrected.
Controls the decision to increase or decrease the poll interval for the system. Controls whether or not the DC will respond to time sync requests that use older authentication protocols. Specifies the amount of time that a suspicious offset must persist before it is accepted as correct in seconds. An unsigned integer that indicates the time jump audit threshold, in seconds.
Specifies the number of clock ticks between phase correction adjustments. Value of 1 indicates that W32Time uses multiple SSL timestamps to seed a clock that is grossly inaccurate. Indicates that non-standard mode combinations are allowed in synchronization between peers. The default value for domain members is 1. Specifies a space-delimited list of peers from which a computer obtains time stamps, consisting of one or more DNS names or IP addresses per line.
Computers connected to a domain must synchronize with a more reliable time source, such as the official U. The default value on stand-alone clients and servers is time. Indicates which peers to accept synchronization from: NoSync.
The time service does not synchronize with other sources. The time service synchronizes from the servers specified in the NtpServer. The time service synchronizes from the domain hierarchy. The time service uses all the available synchronization mechanisms. The default value on domain members is NT5DS. The default value on stand-alone clients and servers is NTP. The default value for stand-alone clients and servers is 0x Determines whether the service chooses synchronization partners outside the domain of the computer.
The default value for domain members is 2. The default value for stand-alone clients and servers is 2. Specifies the location of the DLL for the time provider. Indicates if the NtpClient provider is enabled in the current Time Service.
Specifies the events logged by the Windows Time service. Specifies the large sample skew for logging, in seconds. Specifies the maximum number of times to double the wait interval when repeated attempts to locate a peer to synchronize with fail. Specifies the initial interval to wait, in minutes, before attempting to locate a peer to synchronize with.
Specifies the special poll interval, in seconds, for manual peers. Indicates that non-standard mode combinations are allowed in synchronization between clients and servers. Indicates if the NtpServer provider is enabled in the current Time Service.
Controls the number of entries created in the Windows Time log file. The default value is none, which does not log any Windows Time activity. This value does not affect the event log entries normally created by Windows Time. Controls the location and file name of the Windows Time log. The default value is blank, and should not be changed unless FileLogEntries is changed.
A valid value is a full path and file name that Windows Time will use to create the log file. Controls the circular logging behavior of Windows Time log files. When FileLogEntries and FileLogName are defined, defines the size, in bytes, to allow the log file to reach before overwriting the oldest log entries with new entries.
Please use or larger value for this setting. After you set the domain functional level to a certain value, you can't roll back or lower the domain functional level, with the following exceptions:. For more information about features available at each of the functional levels, see Forest and domain functional levels. Active Directory Domain Services can't be installed on a server that also runs the following server roles or role services:.
Use the Remote Server Administration Tools for Windows 10 or later to manage domain controllers and other servers that run Windows Server. The following example shows how to upgrade the Contoso forest from a previous version of Windows Server to a later version. This action automatically runs adprep on the earlier version forest and domain. In Server Manager , select the yellow triangle. From the drop-down, select Promote the server to a domain controller. On the Deployment Configuration screen, select Add a new domain to an existing forest and select Next.
On the Prerequisite Check screen, select Install. After the restart has completed, sign in again. You can enter the name of each Operation Master Role or use numbers to specify the roles. To verify the roles were moved, go to the new Windows Server. Demote and remove the earlier Windows Server DC.
For information on how to demote a DC, see Demoting domain controllers and domains. After the server is demoted and removed, you can raise the forest functional and domain functional levels to the latest version of Windows Server. Skip to main content. Additionally, the dates and the times may change when you perform certain operations on the files. Important Windows 7 hotfixes and Windows Server R2 hotfixes are included in the same packages.
However, hotfixes on the Hotfix Request page are listed under both operating systems. Always refer to the "Applies To" section in articles to determine the actual operating system that each hotfix applies to. GDR service branches contain only those fixes that are widely released to address widespread, critical issues.
LDR service branches contain hotfixes in addition to widely released fixes. The security catalog files, for which the attributes are not listed, are signed with a Microsoft digital signature. Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section. For more information about software update terminology, click the following article number to view the article in the Microsoft Knowledge Base:.
Need more help? Expand your skills. Get new features first. Was this information helpful? Yes No. Thank you! Any more feedback? The more you tell us the more we can help.
Can you help us improve?
0コメント